New EASUN charge controller installed and went into “Night Mode, No Charging”.

softdown
softdown Solar Expert Posts: 4,001 ✭✭✭✭
edited August 21 in Off Grid Solar & Battery Systems #1
Yet battery voltage is only 56.3. Default settings:
Bulk: 59.2V
Float: 58.4V
Absorb: 55.2V

I have the manual. It is maybe OK. Dancing with electronic keys is not my forte at all. I can’t even get the temperature off of the C/Celcius setting. 

4.2 star rating. I have found ratings below 4.4 to indicate incoming issues. Which can usually be overcome with a time and anxiety price being extracted. 

* Should I Just wait until tomorrow morning and see if it likes charging batteries sitting at ~ 48.4 volts?  This string is not required but I got it done for less than $250. So why not. Bad weather happens. 

*Or drive myself nuts pushing, so far, uncooperative electronic keys? Maybe fix it? Maybe it is already ok? 
First Bank:16 180 watt Grape Solar with  FM80 controller and 3648 Inverter....Fullriver 8D AGM solar batteries. Second Bank/MacGyver Special: 10 165(?) watt BP Solar with Renogy MPPT 40A controller/ and Xantrex C-35 PWM controller/ and Morningstar PWM controller...Cotek 24V PSW inverter....forklift and diesel locomotive batteries
· Share on Twitter

Comments

  • softdown
    softdown Solar Expert Posts: 4,001 ✭✭✭✭
    #2
    Correction edits stymied. Here goes: Bulk:58.4        Float: 55.2V
    First Bank:16 180 watt Grape Solar with  FM80 controller and 3648 Inverter....Fullriver 8D AGM solar batteries. Second Bank/MacGyver Special: 10 165(?) watt BP Solar with Renogy MPPT 40A controller/ and Xantrex C-35 PWM controller/ and Morningstar PWM controller...Cotek 24V PSW inverter....forklift and diesel locomotive batteries
    · Share on Twitter
  • BB.
    BB. Super Moderators, Administrators Posts: 33,704 admin
    #3
    What is the array voltage (specs/measured)?

    -Bill
    Near San Francisco California: 3.5kWatt Grid Tied Solar power system+small backup genset
    · Share on Twitter
  • softdown
    softdown Solar Expert Posts: 4,001 ✭✭✭✭
    #4
    118 volts from three panels. Voltage taken right off of the panels.  145/150V charge controller. 

    A lot could have gone wrong. I’ll troubleshoot further tomorrow. Or so. 

    Dancing with electronic keys gives me the creeps. I’ve had some bad experiences. I am not real good at it.
    First Bank:16 180 watt Grape Solar with  FM80 controller and 3648 Inverter....Fullriver 8D AGM solar batteries. Second Bank/MacGyver Special: 10 165(?) watt BP Solar with Renogy MPPT 40A controller/ and Xantrex C-35 PWM controller/ and Morningstar PWM controller...Cotek 24V PSW inverter....forklift and diesel locomotive batteries
    · Share on Twitter
  • littleharbor2
    littleharbor2 Solar Expert Posts: 2,159 ✭✭✭✭✭
    #5
    I had a situation with a Midnight solar controller one time where the internal clock was wrong and it was doing something similar to what you're saying is happening. Check to see if there's a clock in that controller

    2.1 Kw Suntech 175 mono, Classic 200, Trace SW 4024 ( 15 years old  but brand new out of sealed factory box Jan. 2015), Bogart Tri-metric,  460 Ah. 24 volt LiFePo4 battery bank. Plenty of Baja Sea of Cortez sunshine.

    · Share on Twitter
  • softdown
    softdown Solar Expert Posts: 4,001 ✭✭✭✭
    #6
    So I managed to blow up the panel diodes again. Doing the same thing as the last successful string - I think. Usually I don’t blow up diodes. Usually. 

    There is something important that I forgot to do? 

    Replacing the diodes underneath the panels will be pretty uncomfortable. May remove them for easier access. 
    First Bank:16 180 watt Grape Solar with  FM80 controller and 3648 Inverter....Fullriver 8D AGM solar batteries. Second Bank/MacGyver Special: 10 165(?) watt BP Solar with Renogy MPPT 40A controller/ and Xantrex C-35 PWM controller/ and Morningstar PWM controller...Cotek 24V PSW inverter....forklift and diesel locomotive batteries
    · Share on Twitter

Categories