Conext ComBox - Firmware update released

mike95490 · August 2015

Argh, the last few days, my logging has been squirrely and incomplete. I found the uSD card in the combox was corrupted and reformatted it, Reinstalled the same card and rebooted the combox, and tonight, got
Internal Memory Full - Directories: nand:0:\Energy\2015\08.nand:0:\2015\08. Purged.
??
So a quick google gives me:
Why has my Combox stopped logging system energy graphs?
Energy graphs are stored in the Combox's internal memory. Older firmware would cause the Combox to quit logging once internal
memory was full. Uprading the firmware of the Combox will allow the data to "wrap", allowing the oldest data to drop off, making room for more data.
The latest Combox firmware can be uploaded to a thumb drive from our website.
http://solar.schneider-electric.com/...conext-combox/

I'm running
Application Version Ver02.01BN0673
Application Build Date 2014-09-19_10-40-25
and the latest version is now
http://solar.schneider-electric.com/...conext-combox/
Conext Combox Firmware (3.00 Build 707) – NEW
http://cdn.solar.schneider-electric....ld-707-new.zip

So tomorrow I try updating, wish me luck

Conext Combox Firmware (3.00 Build 707) – NEW
Release Notes For Conext Combox/Conext Modbus
Converter
Version: 03.00 Build 707 [14 Feb, 2015]
New Features
• CSW Upgrade support on new configurations, warnings and faults.
• Added support for users to perform custom data logging on Modbus device
parameters.
• Added support for AGS auto start/stop based on Battery SOC.
• Added support to emulate USB device connect/disconnect from software.
Bug Fixes
• Updated boot loader to version (Ver01.03BN0118 ) to support watchdog timer
in boot loader mode.
• Added support to update watchdog timer during application initialization
stages.
• Added support to display negative load power for CSW.
• Changed timestamp from GMT to local time in the portal_test script.
• Added support to display normalized Battery bank SOC readings on WebUI
home screen.
• Updated cloud push scripts to use content-length meta data instead of using
chunked transfer encoding which has shown to cause problems on some sites
on web portal.
• Ensures that the associations on CSW are not allowed to be changed during
operation mode.
Note
• The new bootloader (Ver01.03BN0118 ) might be incompatible with
application firmware prior to V03.00. Therefore, it is not recommended to
downgrade the application firmware upon the upgrade of the new bootloader.
Version: 02.01 Build 673 [19 Sep, 2014]
New Features
• Energy odometer (KWh meters) nightly backup to an installed SD card
• Removed unused run-time counters in email report
• Changed GVS and GFS configuration settings to two decimal places
• Added Battery Monitor “Synchronize Now” command
Bug Fixes
• Fixed configuration issues which causes System Configuration Fault on startup
• Fixed overflow bug in energy calculation for battery monitor power flow
• Fixed dashboard corruption when updating from an earlier firmware version
• Removed unused curtailment percentage from system Modbus map
• Fixed AC Transfer switch delay settings
• Fixed GVS and GFS configuration settings
• Fixed schedule timing error when using data push to cloud service

////// update
all seems to have gone well,
WAS
Application Version Ver02.01BN0673
Application Build Date 2014-09-19_10-40-25
Bootloader Version Ver01.01BN0058
Bootloader Build Date 2013-05-01_17-34-02

after upgrade:
Application Version Ver03.00BN0707
Application Build Date 2015-02-14_02-44-31
Bootloader Version Ver01.03BN0118
Bootloader Build Date 2014-12-16_12-18-33

Sadly, while the error message is gone now, the logging still seems inoperable, Maybe it will "cure" itself after a 24 hour cycle (unlikely) Looks like I'm calling schneider

new2PV · August 2015

Interesting I can;t sync my battery monitor with the new firmware, says the value can;t be changed...or in this case enabled.

mike95490 · August 2015

Internal Memory Full - Directories: nand:0:\Energy\2015\08.nand:0:\2015\08. Purged.

apparently this is fatal, and they asked for proof of purchase to ship me a new one.

SkiDoo55 · August 2015

II

mike95490 wrote: »

apparently this is fatal, and they asked for proof of purchase to ship me a new one.

You can download a script that will clear and reset the cache. You can save the data first from memory. There is another script so be aware that will reset back to factory which will wipe all of your settings. This same thing happened to me a couple of months ago, reset internal memory logging all is happy. No ComBox change out. Tech support said it was a bug in code. Code should do FIFO with the files, purge the oldest to make room for new logs. Should be corrected with next firmware update whenever that is?
Under tech pubs for the ComBox on the Schneider site reset logs script!!

mike95490 · August 2015

I've tried the script, and hope it works, the results file says the right things happened. Just waiting a day now to see if it's working.
Thanks for the tip SkiDoo55

SkiDoo55 · August 2015

Old

mike95490 wrote: »

I've tried the script, and hope it works, the results file says the right things happened. Just waiting a day now to see if it's working.
Thanks for the tip SkiDoo55

Let us know, worked fine on mine, glad I got a tech rep that knew what to do. Been pretty lucky with support so far. He said it is nothing wrong with the hardware was a code bug that got out in last firmware. Is scheduled to be fixed in next release when ever that will be. I had about 3 years of energy data on mine. Though it was supposed to hold 5 but guess not! Another feature should (mentioned by tech) be ability to record it to the micro SD card.

mike95490 · August 2015

yes, the reset script worked, I am happy again. But there is a replacement in the mail, and I was sent a return postage label, so I'll test them both for a bit, before sending one back.

Tinbum · November 2015

I hope you can help. I am about to buy a Conex Combox but the part number I require, 865-1058, seems to be very hard to get. There are a other part numbers for the combox eg 809-0918 that is more readily available. Is it a firmware difference and is the firmware interchangeable?

new2PV · November 2015

I wish I could help you but I just don;t know, Schneider told me they were different on the phone.

SkiDoo55 · November 2015

A new ComBox firmware release on the Schnieder site. Haven't flashed mine yet, been busy.
They also have a new script tool to clear the internal memory with instructions for users that are getting a internal memory full error. Maybe the new firmware might take care of that. Hope they put the ability in to log energy etc to external card?

Dave Angelini · November 2015

Tinbum said:

I hope you can help. I am about to buy a Conex Combox but the part number I require, 865-1058, seems to be very hard to get. There are a other part numbers for the combox eg 809-0918 that is more readily available. Is it a firmware difference and is the firmware interchangeable?

They are available from the store here. The more expensive model 865 1058 is what you want for an XW or SW. The other model is for the marine world and would be a mistake to buy as the firmware is different!

new2PV · November 2015

If its just a firmware change buy the cheaper box and flash it, what is the issue with doing that?

Dave Angelini · November 2015

Go ahead and try it.! It is a different model number for a reason.

new2PV · November 2015

So the schneider tech was correct, the xw needs the correct part number to work.

Dave Angelini · November 2015

Good that you looked into it. Not good to tell people to do the wrong thing even on the internet.

Tinbum · December 2015

Thanks for the replies. I did buy one of these but had to have it shipped to a friend in New York who was then sending it to me in the UK with an MPPT 80 600. I'd asked him to put it within the MPPT box but in his wisdom he didn't and despite me having only ordered on parcel for collection the courier took the two saying it was ok. It was never seen again and because I had only ordered one collection the courier wont pay out as one was delivered- good old DHL. I can't seem to find them in the UK and no one want to send one from USA and if the do they want a ridicules amount to do it.

Dave Angelini · December 2015

Keep looking in the UK. I have client their and I will ask him also. We drop shipped from Sacramento into London so I know it can be done.

rpvietzke · January 2017

There is another version of the combos firmware uploaded at the Schneider site. There also appear to be a couple updates posted for the CSW, AGS, BattMon that I haven't seen before, although the dates indicate they are not totally new.

Combox is up to 3.03 BN 830 at: ComBox Firmware VER 3.03 BN 830

Rob

Dave Angelini · January 2017

Some good things here maybe for folks using AGS.

mike95490 · January 2017

thanks. I see nothing there that benefits me, so I'll pass on this round, But the recovering for bricked gear looks nice.

Rossman · May 2017

SkiDoo55 said:

II

mike95490 wrote: »

apparently this is fatal, and they asked for proof of purchase to ship me a new one.

You can download a script that will clear and reset the cache. You can save the data first from memory. There is another script so be aware that will reset back to factory which will wipe all of your settings. This same thing happened to me a couple of months ago, reset internal memory logging all is happy. No ComBox change out. Tech support said it was a bug in code. Code should do FIFO with the files, purge the oldest to make room for new logs. Should be corrected with next firmware update whenever that is?
Under tech pubs for the ComBox on the Schneider site reset logs script!!

Anyone got an url for this script? I can't find shit on the SE site

Having same issue with the logs being full. Thanks!

mike95490 · May 2017

http://solar.schneider-electric.com/product/conext-combox/
Downloads
TechPublications
You want

and

and under FIRMWARE you want to have the latest for you box.
After you backup your data, the firmware update may fix all the issues,

And get a microSD card for the box. That's how I do the backups

Pay attention to EVERY Word in the doc for the scripts, The wording and sequence is not consumer friendly,
these are technical documents.

I don't know any way to capture / save the existing data unless you do each one manually (painful)

maximus · July 2017

Hello I know this is an old post but I need your help, just bought conext combox and the default firmware is

Device Info: Conext ComBox - Freedom SW by Xantrex

Model Number: 809-0918

Serial Number: B12946247

Hardware Revision: Rev-H

Device Name: ComBox-B12946247

MAC Address: 00-00-54-FE-0D-8C

IP Address: 192.168.1.12

Hostname: cb-B12946247

Software ID: 150-0288

Kernel Version: 1.33

Application Version: Ver01.00BN0044

Application Build Date: 2014-02-27_16-18-42

Boot Loader Version: Ver01.02BN0087

Boot Loader Build Date: 2013-08-23_09-40-38

Modbus Map Version: A.2

with this firmware I can see two MPPT60 perfect but I can´t see the 2 inverters and AGS, can anyone have the Application Version: Ver01.00BN0044 or other version before 3.0 or someone can tell me if its possible backup the firmware from combox??, thanks a lot.

Dave Angelini · July 2017

Combox for Freedom SW is not the same as Combox for XW and CSW. I do not believe there is a way to get this to work correctly.
Combox for XW & CSW is model 865-1058 and is for renewable energy inverters. Your is for Marine Inverters.

Image: https://us.v-cdn.net/6024911/uploads/editor/a6/f293mkgg37uc.png

Dave Angelini · July 2017

You must have me confused with someone else

Solray · July 2017

Dave Angelini said:

You must have me confused with someone else

That was weird and out of no where... lol

tampasolar · October 2017

What is GFS Enable in the ComBox

tampasolar · October 2017

Thats under Active Power Control for the XW device

tampasolar · October 2017

Also connot find documentation for Generator Support Plus under Advanced Features in the ComBox

tampasolar · October 2017

Would love it I anyone could post a link to any manual that has these items in it. Thanks.

Conext ComBox - Firmware update released

Comments

Categories