Divert Plumbing Vents on Roof (Solution)

JacobVargas
JacobVargas Registered Users, Users Awaiting Email Confirmation Posts: 1 ✭
in Construction #1
Finally found a solution to divert those vent pipes.  They're always taking up space in which extra panels could be, such a waste.
Code changes now allow for a product called Solar Roof Jack to Divert.   Haven't had any problems with inspectors and they all give instant approval.

www.SolarRoofJack.com




Tagged:
· Share on Twitter

Comments

  • mike95490
    mike95490 Solar Expert Posts: 9,583 ✭✭✭✭✭
    #2
    The roof vents are often the easiest way for a plumber with a snake to clear a clog.  Most houses don't have clean-out plugs, and if you can't snake through a roof vent, you have to open lines up under a sink - messy and stinky.

    Powerfab top of pole PV mount | Listeroid 6/1 w/st5 gen head | XW6048 inverter/chgr | Iota 48V/15A charger | Morningstar 60A MPPT | 48V, 800A NiFe Battery (in series)| 15, Evergreen 205w "12V" PV array on pole | Midnight ePanel | Grundfos 10 SO5-9 with 3 wire Franklin Electric motor (1/2hp 240V 1ph ) on a timer for 3 hr noontime run - Runs off PV ||
    || Midnight Classic 200 | 10, Evergreen 200w in a 160VOC array ||
    || VEC1093 12V Charger | Maha C401 aa/aaa Charger | SureSine | Sunsaver MPPT 15A

    solar: http://tinyurl.com/LMR-Solar
    gen: http://tinyurl.com/LMR-Lister ,

    · Share on Twitter
  • DanS26
    DanS26 Solar Expert Posts: 269 ✭✭✭
    #3
    I'd like to hear from the plumbing experts about having vent pipes lay horizontally in freezing weather conditions.  Especially long horizontal runs. 
    23.16kW Kyocera panels; 2 Fronius 7.5kW inverters; Nyle hot water; Steffes ETS; Great Lakes RO; Generac 10kW w/ATS, TED Pro System monitoring
    · Share on Twitter
  • littleharbor2
    littleharbor2 Solar Expert Posts: 2,109 ✭✭✭✭✭
    edited November 2017 #4
    I see very little benefit to these other than, for aesthetic reasons, being able to squeeze another panel in that will spend the majority of its time in the shadow of a vent. Might as well put a dummy panel there.

    2.1 Kw Suntech 175 mono, Classic 200, Trace SW 4024 ( 15 years old  but brand new out of sealed factory box Jan. 2015), Bogart Tri-metric,  460 Ah. 24 volt LiFePo4 battery bank. Plenty of Baja Sea of Cortez sunshine.

    · Share on Twitter
  • Estragon
    Estragon Registered Users Posts: 4,496 ✭✭✭✭✭
    #5
    If using such a thing, why wouldn't you run the opening to the north side of the array? That would avoid shadowing and provide roof slope to the +/- horizontal part for drainage.
    Off-grid.  
    Main daytime system ~4kw panels into 2xMNClassic150 370ah 48v bank 2xOutback 3548 inverter 120v + 240v autotransformer
    Night system ~1kw panels into 1xMNClassic150 700ah 12v bank morningstar 300w inverter
    · Share on Twitter
  • littleharbor2
    littleharbor2 Solar Expert Posts: 2,109 ✭✭✭✭✭
    edited November 2017 #6
    Estragon said:
    If using such a thing, why wouldn't you run the opening to the north side of the array? That would avoid shadowing and provide roof slope to the +/- horizontal part for drainage.

    That would make more sense than the way it is being presented. Or just relocate the vent from inside the attic.  

    2.1 Kw Suntech 175 mono, Classic 200, Trace SW 4024 ( 15 years old  but brand new out of sealed factory box Jan. 2015), Bogart Tri-metric,  460 Ah. 24 volt LiFePo4 battery bank. Plenty of Baja Sea of Cortez sunshine.

    · Share on Twitter
  • LisaTiani
    LisaTiani Registered Users, Users Awaiting Email Confirmation Posts: 1 ✭
    #7
    Hi everyone I'm new to the site and I saw the product solar roof Jack. To me it seems like a great idea. I currently have several projects where roof vents are an issue. If they can actually be used where they are run under the panels and out of the way then the efficiency of the solar system would be much higher. This means less panels needed that are cost for the customer easier sell for me. Has anybody used these and had an issue with them?
    · Share on Twitter
  • Dave Angelini
    Dave Angelini Solar Expert Posts: 6,905 ✭✭✭✭✭✭
    #8
    If you have enough space and height one can redesign the vent system and use 1/3 of the vents.

    Maybe someone else knows about the product roof jack. Sounds like more feet on the roof to me.

    I would much rather use a ground mount or a pergola and leave the roof alone.




    "we go where power lines don't" Sierra Nevada mountain area
       htps://offgridsolar1.com/
    E-mail offgridsolar@sti.net

    · Share on Twitter
  • BB.
    BB. Super Moderators, Administrators Posts: 33,623 admin
    #9
    I am guessing you are asking about this product?

    https://solarroofjack.com/ (for example)


    You probably need to talk with your AHJ (building department/inspector) to see if they would accept these offset vents...

    I have a bit of a concern--At times the easiest (only?) method to clear a stopped drain was to put a snake down through the roof vent. These "hard 90 degree turns) could make it very difficult to put a snake through these offset vents.

    -Bill "not a plumber" B.
    Near San Francisco California: 3.5kWatt Grid Tied Solar power system+small backup genset
    · Share on Twitter

Categories